Unix/Linux Command Reference

The simplest way to complete installation or uninstallation of SafeNet ProtectToolkit-C, or to change the Cryptoki provider on any of the Unix/Linux platforms, is to use the Unix Installation Utility. The utility ensures that the correct commands for your platform are executed automatically. See Using the Unix Installation Utility for more information.

If you wish to enter platform-specific commands manually, use the commands in this section.

Manual Installation

Before adding or removing packages, you must become the super-user on the host system.

NOTE The Runtime and SDK packages cannot be installed concurrently. To switch from one package to the other, uninstall the package that is no longer required and then install the new one.

The Runtime and SDK packages are packaged using the standard packaging software for each system. The latest versions of the client software and HSM firmware can be found on the Gemalto Technical Support Customer Portal. See Support Contacts for more information.

To install the software on your host system

1.Refer to the following table for the name of the package to be installed on your operating system.

Linux Platforms
Runtime package	PTKcprt
SDK package	PTKcpsdk

2.Refer to the following table for the package required and locate the row for the correct operating system, as installed on the host system. Use the program and commands listed to install the software.

Runtime Package
Operating System	Program	Example Commands
Solaris (SPARC & Intel)	pkgadd(1M)	pkgadd -d /cdrom/Solaris/PTKC_Runtime
Linux	rpm(8)	cd <path to directory>/Linux/PTKC_Runtime rpm -i PTKcprt-x.xx-y.i386.rpm (where `x.xx-y` refers to the version of the software)
AIX	installp	cd <path to directory>/AIX/PTKC_Runtime installp -acgNQqwX -d . PTKcprt.rte
HP-UX	swinstall	cd <path to directory>/HP-UX/PTKcpr swinstall PTKcprt.depot

SDK Package
Operating System	Program	Example Commands
Solaris (SPARC & Intel)	pkgadd(1M)	pkgadd -d /cdrom/Solaris/PTKC_SDK
Linux	rpm(8)	cd <path to directory>/Linux/PTKC_SDK rpm -i PTKcpsdk-x.xx-y.i386.rpm (where `x.xx-y` refers to the version of the software)
AIX	installp	cd <path to directory>/AIX/PTKC_SDK installp -acgNQqwX -d . PTKcpsdk.rte
HP-UX	swinstall	cd <path to directory>/HP-UX/PTKcpsdk swinstall PTKcpsdk.depot

3.Add the /opt/safenet/protecttoolkit5/ptk/bin directory to the execution path and the /opt/safenet/protecttoolkit5/ptk/lib directory to the library path. The following commands may be used to configure your paths for the sh(1) shell. Please consult your operating system manual for other shells.

Operating System	Commands
Solaris (SPARC & Intel) Linux	PATH=$PATH:/opt/safenet/protecttoolkit5/ptk/bin export PATH LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/opt/safenet/protecttoolkit5/ptk/lib export LD_LIBRARY_PATH
Solaris (x86) 64-bit	PATH=$PATH:/opt/safenet/protecttoolkit5/ptk/bin/amd64 export PATH LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/opt/safenet/protecttoolkit5/ptk/lib export LD_LIBRARY_PATH
AIX	PATH=$PATH:/opt/safenet/protecttoolkit5/ptk/bin export PATH LIBPATH=$LIBPATH:/opt/safenet/protecttoolkit5/ptk/lib export LIBPATH
HP-UX	PATH=$PATH:/opt/safenet/protecttoolkit5/ptk/bin export PATH SHLIB_PATH=$SHLIB_PATH:/opt/safenet/protecttoolkit5/ptk/lib export SHLIB_PATH

Once installed, the software is ready to use under /opt/SafeNet/protecttoolkit5.

Changing the Cryptoki Provider manually

This section applies to the SDK package only.

Different SafeNet ProtectToolkit-C Cryptoki provider files are required if an HSM is present (PCI or network mode) or not (software-only mode).

Both Cryptoki provider files are installed with the SDK package. On Unix/Linux systems, the software-only Cryptoki provider is made active by default.

To change the default Cryptoki provider selection

Remove the soft-link:

/opt/safenet/protecttoolkit5/ptk/lib/libcryptoki.so or
/opt/safenet/protecttoolkit5/ptk/lib/libcryptoki.a (for AIX)

and recreate it to point to the SafeNet HSM Cryptoki provider. For example, the following shell commands may be used to enable the HSM (executed as the super-user):

# cd /opt/safenet/protecttoolkit5/ptk/lib
# rm libcryptoki.so
# ln -s libcthsm.so libcryptoki.so

The following shell commands may be used to enable the software emulation (executed as the super-user):

# cd /opt/safenet/protecttoolkit5/ptk/lib
# rm libcryptoki.so
# ln -s libctsw.so libcryptoki.so

Manual uninstallation

Before adding or removing any packages, you must become the super-user on the host system.

To uninstall the software from your host system

1.Identify the name of the package to be uninstalled from your system.

Linux, Solaris and AIX Platforms
Runtime package	PTKcprt
SDK package	PTKcpsdk

2.Use the program and command listed to remove the software, where <package name> is the correct name of the package to be uninstalled.

Operating System	Program	Command
Solaris (SPARC & Intel)	pkgrm(1M)	pkgrm <package name>
Linux	rpm(8)	rpm -e <package name>
AIX	installp*	installp -u <package name>
HP-UX	swremove	swremove <package name>

* smit can also be used

** sam can also be used